View SMA6860M_4997818.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SMA6860M Series
High Voltage 3-Phase Motor Drivers
Features and Benefits
Built-in pre-drive IC MOSFET power element Alleviate noise generation by adjusting an internal resistor CMOS compatible input (5 V) High-side gate driver using bootstrap circuit or floating power supply Built-in protection circuit for controlling power supply voltage drop (UVLO on VCC) Overcurrent protection (OCP), overcurrent limiting (OCL), and thermal shutdown (TSD) Output of fault signal during operation of protection circuit Output current 1.5, 2, or 2.5 A Small SIP (SMA 24-pin)
Description
The SMA6860M inverter power module (IPM) series provides a robust, highly-integrated solution for optimally controlling 3-phase motor power inverter systems and variable speed control systems used in energy-conserving designs to drive motors of residential and commercial appliances. These ICs take 230 VAC input voltage, and up to 2.5 A (continuous) output current. They can withstand voltages of up to 500 V (MOSFET breakdown voltage). The SMA6860M power package includes an IC with all of the necessary power elements (six MOSFETs), pre-driver ICs (two), and bootstrap diodes (three), needed to configure the main circuit of an inverter. This enables the main circuit of the inverter to be configured with fewer external components than traditional designs. Applications include residential white goods (home applications) and commercial appliance motor control: * Air conditioner fan * Small ventilation fan * Dishwasher pump
Packages: Power SIP
Not to scale
Leadform 2451
Leadform 2452
Functional Block Diagram
VB1 VB2 VB3
VCC1
UVLO
UVLO
UVLO
UVLO
VBB
HIN1 HIN2 HIN3 COM1 SD1 VCC 2
Input Logic
High-Side Level Shift Driver
W1 W2 V U UVLO
LIN1 LIN2 LIN3 COM2 SD2 OCL RC
Input Logic (OCP Reset ) Thermal Shutdown OCP
Low-Side Driver
LS 2 OCP and OCL LS1
Figure 1. Driver block diagram.
28610.12, Rev. 3
A. SD1, SD2 terminals are used for both input and output. B. SD1, SD2, and OCL terminals are open-collector output. RC terminal is open-drain output. C. Blanking Time (tblank) is used in Overcurrent Limiting (OCL) and Overcurrent Protection (OCP). If the time exceeds the limit, the signal will be output (open-collector output turns on), and protection operation will start up.
SMA6860M Series
Selection Guide
Part Number SMA6861M SMA6862M SMA6863M Packing 18 pieces per tube 18 pieces per tube 18 pieces per tube
High Voltage 3-Phase Motor Drivers
MOSFET Breakdown Voltage, VDSS(min) (V) 250 500 500
Output Current Continuous, IO(max) (A) 2 1.5 2.5 Pulsed, IOP (max) (A) 4 3 5
Absolute Maximum Ratings, valid at TA = 25C
Characteristic
MOSFET Breakdown Voltage Logic Supply Voltage Bootstrap Voltage Output Current, Continuous
Symbol
SMA6861M VDSS VCC VBS IO SMA6862M SMA6863M Between VCC and COM
Remarks
VCC = 15 V, ID = 100 A, VIN = 0 V
Rating
250 500 500 20 20 2 1.5 2.5 4
Unit
V V V V V A A A A A A V V V W C/W C/W C C C
Between VB and HS (U,V, and W phases) SMA6861M SMA6862M SMA6863M SMA6861M
Output Current, Pulsed Input Voltage Pull-up Voltage for Shutdown Pins Pull-up Voltage for Overcurrent Limiting Pin Allowable Power Dissipation Thermal Resistance (Junction to Case) Thermal Resistance (Junction to Ambient) Case Operating Temperature Junction Temperature (MOSFET) Storage Temperature
IOP VIN VSDX VOCL PD RJC RJA TCOP TJ Tstg
SMA6862M SMA6863M
PW 100 s, duty cycle = 1%
3 5 -0.5 to 7 7 7 28 4.46 31.25 -20 to 100 150 -40 to 150
HINx and LINx pins SDx pins TC = 25C All elements operating All elements operating
All performance characteristics given are typical values for circuit or system baseline design only and are at the nominal operating voltage and an ambient temperature, TA, of 25C, unless otherwise stated.
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
2
SMA6860M Series
High Voltage 3-Phase Motor Drivers
Recommended Operating Conditions
Characteristic Main Supply Voltage VBB Snubber Capacitor Logic Supply Voltage Zener Voltage for VCCx Pins Pull-up Voltage Pull-up Resistor SD2 Pin Pull-up Resistor OCL Pin Pull-up Resistor RC Pin Capacitor SDx Pins Capacitor RC Pin Dead Time Minimum Input Pulse Width Switching Frequency Junction Temperature Symbol SMA6861M VBB CSB VCC VZ VSDx, VOCL RUP2 RUP1 RR CSDX CC tdead IINMIN(on) IINMIN(off) fPWM TJ TJ = -20C to 150C TJ = -20C to 150C TJ = -20C to 150C Between VCC and COM Between VCC and COM SMA6862M SMA6863M Between VBB and LS Remarks Min. - - - 0.01 13.5 18 4.5 3.3 1 33 1 1 1.5 0.5 0.5 - - Typ. - - - - 15 - 5 - - - - - - - - - - Max. 200 400 400 0.1 16.5 20 5.5 10 10 390 10 4.7 - - - 20 125 Units V V V F V V V k k k nF nF s s s kHz C
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
3
SMA6860M Series
Typical Application Diagram
High Voltage 3-Phase Motor Drivers
1
2
3
SMA6860M
10 VB1 VB2 VB3 4 5V RUP1 DZ1 CSD1 5 9 8 7 6 SD1 HIN 1 HIN 2 HIN 3 COM 1 HO 3 HS3 11 13 23 DZ2 LO 1 17 MC U 20 19 18 OCL LVIC LIN1 LIN2 LIN3 LO 2 RS 16 VCC1 HO 1 HS1 24
HVIC
HO 2 HS2 12 M
CSB
VCC 2
RR 5V 5V CC RUP2 CSD2 21 22 15 RC
LO 3 14
SD 2 COM 2
15 V
NOTE: The external electrolytic capacitors should be placed as close to the IC as possible, in order to avoid malfunctions from external noise interference. Put a ceramic capacitor in parallel with the electrolytic capacitor if further reduction of noise susceptibility is necessary.
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
4
SMA6860M Series
Characteristics Logic Supply Current Bootstrap Supply Current Input Voltage Input Voltage Hysteresis Input Current Symbol ICC IBX VIH VIL VIhys IIN VUVHL VUVHH Undervoltage Lock Out VUVHhys VUVLL VUVLH VUVLhys SDx and OCL Output Voltage Overtemperature DetectionThreshold Temperature (Activation and Deactivation) Overcurrent Protection Trip Voltage Overcurrent Limit Reference Voltage Overcurrent Protection Hold Time Blanking Time Bootstrap Diode Leakage Current Bootstrap Diode Forward Voltage Bootstrap Diode Recovery Time Bootstrap Diode Series Resistor MOSFET Breakdown Voltage VSDX(on), VOCL TDH TDL TDhys VTRIP VLIM tp tblank ILBD VFBD trrb RBD SMA6861M VDSS SMA6862M SMA6863M SMA6861M MOSFET Leakage Current IDSS SMA6862M SMA6863M SMA6861M MOSFET On State Resistance RDS(on) SMA6862M SMA6863M SMA6861M MOSFET Diode Forward Voltage VSDF SMA6862M SMA6863M VCC = 15 V VCC = 15 V
High Voltage 3-Phase Motor Drivers
Conditions VCC = 15 V, TC = -20C to 125C VBX = 15 V, VHIN = 5 V, TC = -20C to 125C VCC = 15 V VCC = 15 V VCC = 15 V VIN = 5 V High side, between VBx and U, V, or W High side, hysteresis Low side, between VCC2 and COM2 Low side, hysteresis VSDX = VOCL = 5 V, RUPX = 3.3 k Min - - - 1.6 - - 9.0 9.5 - 10.0 10.5 - - 120 VCC = 15 V, high-side and low side 100 - 0.9 0.5035 - 1.4 VR = 250 V VR = 500 V VR = 500 V - - - - - 168 250 VCC = 15 V, ID = 100 A, VIN = 0 V VCC = 15 V, VDS = 250 V, VIN = 0 V VCC = 15 V, VDS = 500 V, VIN = 0 V VCC = 15 V, VDS = 500 V, VIN = 0 V VCC = 15 V, ID = 1.0 A, VIN = 5 V VCC = 15 V, ID = 1.0 A, VIN = 5 V VCC = 15 V, ID = 1.5 A, VIN = 5 V VCC = 15 V, ISD = 1.0 A, VIN = 0 V VCC = 15 V, ISD = 1.0 A, VIN = 0 V VCC = 15 V, ISD = 1.5 A, VIN = 0 V 500 500 - - - - - - - - - Typ 4.2 135 2.9 2.1 0.8 230 10.0 10.5 0.5 11.0 11.5 0.5 - 135 115 20 1.0 0.53 2.0 2.0 - - - 1.1 70 210 - - - - - - 1.4 3.2 2.0 1.1 1.1 1.1 Max 7 380 3.4 - - 500 11.0 11.5 - 12.0 12.5 - 0.6 150 130 - 1.1 0.5565 - 2.6 10 10 10 1.3 - 252 - - - 100 100 100 1.8 4.0 2.4 1.5 1.5 1.5 Units mA A V V V A V V V V V V V C C C V V ms s A A A V ns V V V A A A V V V
ELECTRICAL CHARACTERISTICS, valid at TA=25C, unless otherwise noted
VRC = 5 V, RR = 360 k, CC = 0.0047 F VCC = 15 V SMA6861M SMA6862M SMA6863M IF = 0.05 A IF / IRP = 100 mA / 100 mA
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
5
SMA6860M Series
High Voltage 3-Phase Motor Drivers
SMA6861M SWITCHING CHARACTERISTICS, valid at TA=25C, unless otherwise noted Characteristics Symbol tdH(on) trH Switching Time, High Side trrH tdH(off) tfH tdL(on) trL Switching Time, Low Side trrL tdL(off) tfL VBB = 150 V, VCC = 15 V, ID = 2.0 A, 0 V VIN 5 V VBB = 150 V, VCC = 15 V, ID = 2.0 A, 0 V VIN 5 V Conditions Min - - - - - - - - - - Typ 660 25 690 630 10 580 50 95 540 15 Max - - - - - - - - - - Units ns ns ns ns ns ns ns ns ns ns
SMA6862M SWITCHING CHARACTERISTICS, valid at TA=25C, unless otherwise noted Characteristics Symbol tdH(on) trH Switching Time, High Side trrH tdH(off) tfH tdL(on) trL Switching Time, Low Side trrL tdL(off) tfL VBB = 300 V, VCC = 15 V, ID = 1.5 A, 0 V VIN 5 V VBB = 300 V, VCC = 15 V, ID = 1.5 A, 0 V VIN 5 V Conditions Min - - - - - - - - - - Typ 720 40 110 670 20 600 40 120 555 20 Max - - - - - - - - - - Units ns ns ns ns ns ns ns ns ns ns
SMA6863M SWITCHING CHARACTERISTICS, valid at TA=25C, unless otherwise noted Characteristics Symbol tdH(on) trH Switching Time, High Side trrH tdH(off) tfH tdL(on) trL Switching Time, Low Side trrL tdL(off) tfL VBB = 300 V, VCC = 15 V, ID = 2.5 A, 0 V VIN 5 V VBB = 300 V, VCC = 15 V, ID = 2.5 A, 0 V VIN 5 V Conditions Min - - - - - - - - - - Typ 790 60 115 725 20 680 70 120 605 20 Max - - - - - - - - - - Units ns ns ns ns ns ns ns ns ns ns
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
6
SMA6860M Series
High Voltage 3-Phase Motor Drivers
OCP Timing Diagram
LIN
LO VTRIP LS1 tblank
OC P Release
S D2 tp RC 3.5 V Slope defined by RC, CC
Low-Side Logic TSD Timing Diagram
Open-collector output transistor turned on in low state
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
7
SMA6860M Series
High Voltage 3-Phase Motor Drivers
High-Side UVLO Timing Diagram
Low-Side UVLO Timing Diagram
LIN
VCC2
UVLH
UVLL
UVLH
LO
SD2
Open-collector output transistor turned on in low state
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
8
SMA6860M Series
High Voltage 3-Phase Motor Drivers
OCL Timing Diagram OCL and SD1 pins connected externally
Enable resumption of high-side operation at next HIN rising edge
HIN
Enable resumption of low-side operation at next LIN rising edge
LIN HO
High-side shutdown
High-side shutdown
3.3 s
3.3 s Low-side shutdown
LO
VTRIP (1 V)
LS1
2 s
2 s 2 s
VOCL (0.5 V)
OCL, SD1
VTH (2.1 V)
VTH (2.9 V) VTH (2.1 V)
VTH (2.9 V)
= 50 Cf
= RLxCf
= RLxCf
VTH (2.9 V)
SD2
= 50 C2
= R2xC2
3.5 V
RC
= 50 CC
5 s
= RRxCC
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
9
SMA6860M Series
High Voltage 3-Phase Motor Drivers
Pin-out Diagrams Leadform 2451
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 3 5 7 9 11 13 15 17 19 21 23
Leadform 2452
2
4
6
8
10
12
14
16
18
20
22
24
Chamfer Side
Chamfer on Opposite Side
Terminal List Table
Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Name VB1 VB2 VB3 VCC1 SD1 COM1 HIN3 HIN2 HIN1 VBB W1 V W2 LS2 RC LS1 OCL LIN3 LIN2 LIN1 COM2 SD2 VCC2 U Function High side bootstrap terminal (U phase) High side bootstrap terminal (V phase) High side bootstrap terminal (W phase) High side logic supply voltage High side shutdown input and UVLO fault signal output High side logic GND terminal High side input terminal (W phase) High side input terminal (V phase) High side input terminal (U phase) Main supply voltage Output of W phase (connect to W2 externally) Output of V phase Output of W phase (connect to W1 externally) Low side source terminal (connect to LS1 externally) Overcurrent protection hold time adjustment input terminal Low side source terminal (connect to LS2 externally) Output for overcurrent limiting Low side input terminal (W phase) Low side input terminal (V phase) Low side input terminal (U phase) Low side GND terminal Low side shutdown input and overtemperature, overcurrent, and UVLO fault signals output Low side logic supply voltage Output of U phase
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
10
SMA6860M Series
High Voltage 3-Phase Motor Drivers
Package Outline Drawing Leadform 2451
Dual rows, 24 alternating pins; pins bent 90 for horizontal case mounting; pin #1 in outer row
Gate protrusion
31.3 0.2 31 0.2
4 0.2
Gate protrusion 1.2 0.1 BSC 10.2 0.2 3 0.5 BSC 2.2 0.7 BSC R1 REF
Branding Area
4.4 REF
View A
C 0.7
+0.15 - 0.05
0.6 +0.15 - 0.05 14 15 16 17 18 19 20 21 22 23 24
1.27 0.1 A 1.27 0.6 B
2.2 0.7 BSC
0.55 +0.2 - 0.1
1
2
3
4
5
6
7
8
9
10
11
12
13
0.7 MAX A Measured at pin exit from case B Measured at pin tips
C Maximum dambar protrusion
0.7 MAX
Leadform: 2451 Terminal core material: Cu Terminal plating: Ni and solder (Sn 97.5%, Ag 2.5%) plating Case material: Epoxy resin Dimensions in millimeters Branding codes (exact appearance at manufacturer discretion): 1st line, lot: YMDD# Where: Y is the last digit of the year of manufacture M is the month (1 to 9, O, N, D) DD is the date # is the tracking letter 2nd line, type: SMA686xM
Deflection at pin bend View A
Leadframe plating Pb-free. Device composition complies with the RoHS directive.
11
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
SMA6860M Series
High Voltage 3-Phase Motor Drivers
Package Outline Drawing Leadform 2452
Dual rows, 24 alternating pins; vertical case mounting; pin #1 opposite chamfer side
Gate protrusion
31.3 0.2 31 0.2
4 0.2
Gate protrusion 10.2 0.2 1.2 0.1 BSC
Branding Area
5 0.5 9.5 +0.7 - 0.5
R1 REF
0.5 +0.15 - 0.05 4.5 REF
1.27 0.5 A View A 0.6 +0.15 - 0.05
4.5 0.5
2
4
6
8
10
12
14
16
18
20
22
24
1 A
3
5
7
9
11
13
15
17
19
21
23
0.7 MAX
0.7 MAX
Measured at pin tips
Leadform: 2452 Terminal core material: Cu Terminal plating: Ni Recommended attachment: Solder dip (Sn-Ag-Cu) Dimensions in millimeters
Deflection at pin bend View A
Branding codes (exact appearance at manufacturer discretion): 1st line, lot: YMDD# Where: Y is the last digit of the year of manufacture M is the month (1 to 9, O, N, D) DD is the date # is the tracking letter 2nd line, type: SMA686xM
Leadframe plating Pb-free. Device composition complies with the RoHS directive.
12
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
SMA6860M Series
High Voltage 3-Phase Motor Drivers
Packing Specification Leadform 2451
Dimensions in millimeters
23.8 . 590
11.5 X
Tube material: PVC Maximum 18 pieces per tube (pins aligned along X direction) Rubber plug each end
130
610
185
Maximum 15 tubes in Y direction Maximum 4 tubes in Z direction Maximum pieces per carton: 18 pieces per tube 15 tubes per layer x 4 layers of tubes 1080 pieces per carton
Z Y
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
13
SMA6860M Series
High Voltage 3-Phase Motor Drivers
Packing Specification Leadforms 2452
Dimensions in millimeters
24.9 590
12.2 X
Tube material: PVC Maximum 18 pieces per tube (pins aligned along X direction) Rubber plug each end
130
610
Maximum 14 tubes in Y direction Maximum 4 tubes in Z direction
185 Z Y
Maximum pieces per carton: 18 pieces per tube 14 tubes per layer x 4 layers of tubes 1008 pieces per carton
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
14
SMA6860M Series
High Voltage 3-Phase Motor Drivers
WARNING -- These devices are designed to be operated at lethal voltages and energy levels. Circuit designs that embody these components must conform with applicable safety requirements. Precautions must be taken to prevent accidental contact with power-line potentials. Do not connect grounded test equipment. The use of an isolation transformer is recommended during circuit development and breadboarding.
Because reliability can be affected adversely by improper storage environments and handling methods, please observe the following cautions. Cautions for Storage * Ensure that storage conditions comply with the standard temperature (5C to 35C) and the standard relative humidity (around 40 to 75%); avoid storage locations that experience extreme changes in temperature or humidity. * Avoid locations where dust or harmful gases are present and avoid direct sunlight. * Reinspect for rust on leads and solderability of products that have been stored for a long time. Cautions for Testing and Handling When tests are carried out during inspection testing and other standard test periods, protect the products from power surges from the testing device, shorts between adjacent products, and shorts to the heatsink. Remarks About Using Silicone Grease with a Heatsink * When silicone grease is used in mounting this product on a heatsink, it shall be applied evenly and thinly. If more silicone grease than required is applied, it may produce stress. * Volatile-type silicone greases may permeate the product and produce cracks after long periods of time, resulting in reduced heat radiation effect, and possibly shortening the lifetime of the product. * Our recommended silicone greases for heat radiation purposes, which will not cause any adverse effect on the product life, are indicated below: Type G746 YG6260 SC102 Suppliers Shin-Etsu Chemical Co., Ltd. Momentive Performance Materials, Inc. Dow Corning Toray Silicone Co., Ltd.
Heatsink Mounting Method Torque When Tightening Mounting Screws. The recommended tightening torque for this product package type is: 58.8 to 78.4 N*cm (6.0 to 8.0 kgf*cm). Soldering * When soldering the products, please be sure to minimize the working time, within the following limits: 2605C 10 s 3805C 5s
*
Soldering iron should be at a distance of at least 1.5 mm from the body of the products
Electrostatic Discharge * When handling the products, operator must be grounded. Grounded wrist straps worn should have at least 1 M of resistance to ground to prevent shock hazard. Workbenches where the products are handled should be grounded and be provided with conductive table and floor mats. When using measuring equipment such as a curve tracer, the equipment should be grounded. When soldering the products, the head of soldering irons or the solder bath must be grounded in other to prevent leak voltages generated by them from being applied to the products. The products should always be stored and transported in our shipping containers or conductive containers, or be wrapped in aluminum foil.
* * *
*
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
15
SMA6860M Series
High Voltage 3-Phase Motor Drivers
The products described herein are manufactured in Japan by Sanken Electric Co., Ltd. for sale by Allegro MicroSystems, Inc. Sanken and Allegro reserve the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Therefore, the user is cautioned to verify that the information in this publication is current before placing any order. When using the products described herein, the applicability and suitability of such products for the intended purpose shall be reviewed at the users responsibility. Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to society due to device failure or malfunction. Sanken products listed in this publication are designed and intended for use as components in general-purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). Their use in any application requiring radiation hardness assurance (e.g., aerospace equipment) is not supported. When considering the use of Sanken products in applications where higher reliability is required (transportation equipment and its control systems or equipment, fire- or burglar-alarm systems, various safety devices, etc.), contact a company sales representative to discuss and obtain written confirmation of your specifications. The use of Sanken products without the written consent of Sanken in applications where extremely high reliability is required (aerospace equipment, nuclear power-control stations, life-support systems, etc.) is strictly prohibited. The information included herein is believed to be accurate and reliable. Application and operation examples described in this publication are given for reference only and Sanken and Allegro assume no responsibility for any infringement of industrial property rights, intellectual property rights, or any other rights of Sanken or Allegro or any third party that may result from its use.
The contents in this document must not be transcribed or copied without Sanken's written consent.
Copyright (c) 2008-2010 Allegro MicroSystems, Inc.
This datasheet is based on Sanken datasheets SSJ-03612, SSJ-03537, and SSJ-03538
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
16
SMA6860M Series
High Voltage 3-Phase Motor Drivers
Worldwide Contacts
Asia-Pacific China Sanken Electric Hong Kong Co., Ltd.
Suite 1026, Ocean Centre Canton Road, Tsimshatsui Kowloon, Hong Kong Tel: 852-2735-5262, Fax: 852-2735-5494
Korea Sanken Electric Korea Co., Ltd.
Samsung Life Yeouido Building 16F 23-10, Yeouido-Dong, Yeongdeungpo-gu Seoul 150-734, Korea Tel: 82-2-714-3700, Fax: 82-2-3272-2145
Sanken Electric (Shanghai) Co., Ltd.
Room 3202, Maxdo Centre Xingyi Road 8, Changning District Shanghai, China Tel: 86-21-5208-1177, Fax: 86-21-5208-1757
Singapore Sanken Electric Singapore Pte. Ltd.
150 Beach Road, #14-03 The Gateway West Singapore 189720 Tel: 65-6291-4755, Fax: 65-6297-1744
Sanken Electric (Shanghai) Co., Ltd. Shenzhen Office
Room 1013, Xinhua Insurance Building Mintian Road, Futian District Shenzhen City, Guangdong, China Tel: 86-755-3391-9356/9358, Fax: 86-755-3391-9368
Europe Sanken Power Systems (UK) Limited
Pencoed Technology Park Pencoed, Bridgend CF35 5HY, United Kingdom Tel: 44-1656-869-100, Fax: 44-1656-869-162
Taiwan Sanken Electric Co., Ltd.
Room 1801, 18th Floor 88 Jung Shiau East Road, Sec. 2 Taipei 100, Taiwan R.O.C. Tel: 886-2-2356-8161, Fax: 886-2-2356-8261
North America United States Allegro MicroSystems, Inc.
115 Northeast Cutoff Worcester, Massachusetts 01606, U.S.A. Tel: 1-508-853-5000, Fax: 1-508-853-7895
Japan Sanken Electric Co., Ltd. Overseas Sales Headquarters
Metropolitan Plaza Building 1-11-1 Nishi-Ikebukuro, Toshima-ku Tokyo 171-0021, Japan Tel: 81-3-3986-6164, Fax: 81-3-3986-8637
Allegro MicroSystems, Inc.
14 Hughes Street, Suite B105 Irvine, California 92618, U.S.A. Tel: 1-949-460-2003, Fax: 1-949-460-7837
Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com
17

▲Up To Search▲

Price & Availability of SMA6860M

	To Download SMA6860M Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .